firmware-analyst – skill Bảo mật cho agent AI

Supporting material availability

This catalog copy contains the inline guidance below, but does not include the following supporting paths. They are external prerequisites, not bundled files:

• ./scripts/getArch.sh
• ./scripts/makeImage.sh
• ./scripts/inferNetwork.sh

Ask for the original supporting material or an existing installation before using a step that depends on these paths; this catalog does not identify a verified download source for them. Resolve each path relative to that installation, inspect its contents, and verify any applicable license and execution prerequisites. Do not run a command or claim a referenced procedure was followed until its required file exists. Do not fabricate the missing scripts or treat an unrelated file with the same name as equivalent. Independent steps fully documented here can proceed within the user’s authorized scope; report any dependent step as unavailable.

> ⚠️ AUTHORIZED USE ONLY

> This skill is for educational purposes or authorized security assessments only.

> You must have explicit, written permission from the system owner before using this tool.

> Misuse of this tool is illegal and strictly prohibited.

> Mandatory confirmation gate

> Before running any command that probes, exploits, changes, persists on, extracts data from, or attempts credential access against a target:

> 1. Ask the user to state the exact target URL, IP, account, or resource.

> 2. Ask the user to confirm written authorization and the permitted scope.

> 3. Show the exact command(s) and explain their expected effect.

> 4. Wait for explicit confirmation in the current conversation.

>

> Without that confirmation, remain read-only and provide defensive guidance only. Prefer a sandbox, disposable VM, or controlled lab.

Firmware acquisition (illustrative)

# Download only from the verified vendor HTTPS source; preserve its hash/signature.
# Substitute the actual approved URL, not this placeholder.
wget https://vendor.example.invalid/firmware/update.bin

# Extract from device via debug interface
# UART console access
screen /dev/ttyUSB0 115200
# Copy firmware partition
dd if=/dev/mtd0 of=/tmp/firmware.bin

# Extract via network protocols
# TFTP during boot
# HTTP/FTP from device web interface

Hardware Methods

UART access         - Serial console connection
JTAG/SWD           - Debug interface for memory access
SPI flash dump     - Direct chip reading
NAND/NOR dump      - Flash memory extraction
Chip-off           - Physical chip removal and reading
Logic analyzer     - Protocol capture and analysis

Use this skill when

• Reviewing authorized embedded firmware images, extracted filesystems or binary security properties
• Planning controlled acquisition, emulation and remediation-oriented reporting

Do not use this skill when

• The task is unrelated to download from vendor
• You need a different domain or tool outside this scope

Instructions

• Clarify goals, constraints, and required inputs.
• Apply relevant best practices and validate outcomes.
• Provide actionable steps and verification.

Extraction and emulation isolation

Keep original firmware immutable and record hash/source/version. Extract untrusted images as an unprivileged user in a disposable VM, with output/resource limits and no host secrets or external network access. chroot is not a security sandbox: the rootful emulation examples must run only inside that isolated VM. Review extraction symlinks/device nodes and tool versions before access. Do not print or reuse discovered credentials; redact reports and keep findings within the authorized disclosure scope.

Firmware Analysis Workflow

Phase 1: Identification

# Basic file identification
file firmware.bin
binwalk firmware.bin

# Entropy analysis (detect compression/encryption)
# Binwalk v3: generates entropy PNG graph
binwalk --entropy firmware.bin
binwalk -E firmware.bin  # Short form

# Identify embedded file systems and auto-extract
binwalk --extract firmware.bin
binwalk -e firmware.bin  # Short form

# String analysis
strings -a firmware.bin | grep -i "password\|key\|secret"

Phase 2: Extraction

# Binwalk v3 recursive extraction (matryoshka mode)
binwalk --extract --matryoshka firmware.bin
binwalk -eM firmware.bin  # Short form

# Extract to custom directory
binwalk -e -C ./extracted firmware.bin

# Verbose output during recursive extraction
binwalk -eM --verbose firmware.bin

# Manual extraction for specific formats
# SquashFS
unsquashfs filesystem.squashfs

# JFFS2
jefferson filesystem.jffs2 -d output/

# UBIFS
ubireader_extract_images firmware.ubi

# YAFFS
unyaffs filesystem.yaffs

# Cramfs
cramfsck -x output/ filesystem.cramfs

Phase 3: File System Analysis

# Explore extracted filesystem
find . -name "*.conf" -o -name "*.cfg"
find . -name "passwd" -o -name "shadow"
find . -type f -executable

# Find hardcoded credentials
grep -r "password" .
grep -r "api_key" .
grep -rn "BEGIN RSA PRIVATE KEY" .

# Analyze web interface
find . -name "*.cgi" -o -name "*.php" -o -name "*.lua"

# Check for vulnerable binaries
checksec --dir=./bin/

Phase 4: Binary Analysis

# Identify architecture
file bin/httpd
readelf -h bin/httpd

# Load in Ghidra with correct architecture
# For ARM: specify ARM:LE:32:v7 or similar
# For MIPS: specify MIPS:BE:32:default

# Set up cross-compilation for testing
# ARM
arm-linux-gnueabi-gcc exploit.c -o exploit
# MIPS
mipsel-linux-gnu-gcc exploit.c -o exploit

Common Vulnerability Classes

Authentication Issues

Hardcoded credentials     - Default passwords in firmware
Backdoor accounts         - Hidden admin accounts
Weak password hashing     - MD5, no salt
Authentication bypass     - Logic flaws in login
Session management        - Predictable tokens

Command Injection

// Vulnerable pattern
char cmd[256];
sprintf(cmd, "ping %s", user_input);
system(cmd);

// Test payloads
; id
| cat /etc/passwd
`whoami`
$(id)

Memory Corruption

Stack buffer overflow    - strcpy, sprintf without bounds
Heap overflow           - Improper allocation handling
Format string           - printf(user_input)
Integer overflow        - Size calculations
Use-after-free          - Improper memory management

Information Disclosure

Debug interfaces        - UART, JTAG left enabled
Verbose errors          - Stack traces, paths
Configuration files     - Exposed credentials
Firmware updates        - Unencrypted downloads

Tool Proficiency

Extraction Tools

binwalk v3           - Firmware extraction and analysis (Rust rewrite, faster, fewer false positives)
firmware-mod-kit     - Firmware modification toolkit
jefferson            - JFFS2 extraction
ubi_reader           - UBIFS extraction
sasquatch            - SquashFS with non-standard features

Analysis Tools

Ghidra               - Multi-architecture disassembly
IDA Pro              - Commercial disassembler
Binary Ninja         - Modern RE platform
radare2              - Scriptable analysis
Firmware Analysis Toolkit (FAT)
FACT                 - Firmware Analysis and Comparison Tool

Emulation

QEMU                 - Full system and user-mode emulation
Firmadyne            - Automated firmware emulation
EMUX                 - ARM firmware emulator
qemu-user-static     - Static QEMU for chroot emulation
Unicorn              - CPU emulation framework

Hardware Tools

Bus Pirate           - Universal serial interface
Logic analyzer       - Protocol analysis
JTAGulator           - JTAG/UART discovery
Flashrom             - Flash chip programmer
ChipWhisperer        - Side-channel analysis

Emulation Setup

QEMU User-Mode Emulation

# Install QEMU user-mode
apt install qemu-user-static

# Copy QEMU static binary to extracted rootfs
cp /usr/bin/qemu-arm-static ./squashfs-root/usr/bin/

# Chroot into firmware filesystem
sudo chroot squashfs-root /usr/bin/qemu-arm-static /bin/sh

# Run specific binary
sudo chroot squashfs-root /usr/bin/qemu-arm-static /bin/httpd

Full System Emulation with Firmadyne

# Extract firmware
./sources/extractor/extractor.py -b brand -sql 127.0.0.1 \
    -np -nk "firmware.bin" images

# Identify architecture and create QEMU image
./scripts/getArch.sh ./images/1.tar.gz
./scripts/makeImage.sh 1

# Infer network configuration
./scripts/inferNetwork.sh 1

# Run emulation
./scratch/1/run.sh

Security Assessment

Checklist

[ ] Firmware extraction successful
[ ] File system mounted and explored
[ ] Architecture identified
[ ] Hardcoded credentials search
[ ] Web interface analysis
[ ] Binary security properties (checksec)
[ ] Network services identified
[ ] Debug interfaces disabled
[ ] Update mechanism security
[ ] Encryption/signing verification
[ ] Known CVE check

Reporting Template

# Firmware Security Assessment

## Device Information
- Manufacture

… (nội dung đầy đủ có trong gói tải về)